ALIDEX
Leading Edge Networking Solutions
 

PG5901

1-Port RS232/485/422 and 2 x Fast-Ethernet RJ45 DNP3.0, Modbus, IEC 60870-5-101/103/104, IEC 61850 Smart Grid Protocol Gateway

Overview
PG5901 Series is a highly reliable and fault tolerant Industrial Protocol Gateway. Its powerful architecture provides seamless conversion between the different protocols Ethernet or Serial based. The serial devices communicating on different protocols could be integrated into the system and extend its reach over the gateway’s redundant Ethernet. This device is designed to work in most demanding industries such as power substations, power generation, oil and gas, farming and manufacturing

Flexibility with Advance Performance

The configuration carried out through a use friendly, Java- Based Windows Utility called eNode Designer. It allows configuring target platforms, set device properties and protocol data point mapping. To do so, a project file representing the system should be created. This will include devices and the protocol applications running on them. The configuration is completely dependent on the “eNode Module” which represents that device or  application – but may include things such as changing the communication port settings and defining where data point information enters and leaves the eNode Designer system.

PG59XX Series embeds an additional layer of security, allowing the devices to be deployed in topologies that request data to flow through the Internet and preventing sensitive control and monitoring data to be readable from malicious activities. IPsec VPN encryption, configurable in both peer-to-peer and peer-to-side modes will make sure the data passing is encrypted through a strong 128, 192 or 256-bit AES encryption.

SE5901 L 2

Features

  • Dual 10/100 Mbps Ethernet port, Optional 802.3af PoE PD capable
  • 1-port RS-232/422/485, baud rate up to 921.6 Kbps
  • IP30 Metal housing with Aluminum heat sink
  • Strong EMC protection, works in environments from -40 to 85°C
  • Same hardware platform for different protocol conversion (Modbus TCP/RTU/ASCII, DNP3.0 TCP or serial, IEC 60870-5-101, IEC 60870-5-103, IEC 60870-5-104, IEC 61850)
  • User friendly configuration with a Java-Based Windows utility
  • Embedded IPsec, PPTP and OpenVPN for enhanced security
  • Management: Web, Device Management Utility, Telnet, SNMPv1/v2c/v3, SMS
protocol gateway  PG5901 DB
PG5901 TB

PG5901 DB - 1x RS232/422/485 (DB9M)+ 2x 10/100Base-TX (RJ45)

PG5901 PoE DB - 1x RS232/422/485 (DB9M)+ 2x 10/100Base-TX (RJ45 / PoE PD)

PG5901 TB - 1x RS232/422/485 (TB)+ 2x 10/100Base-TX (RJ45)

PG5901 PoE TB - 1x RS232/422/485 (TB)+ 2x 10/100Base-TX (RJ45 / PoE PD)

Serial Interface

  • Serial Baud Rate: 1200 bps to 921 Kbps
  • Data Bits: 7, 8 - Stop Bits: 1, 2
  • Parity: odd, even, none, mark, space
  • Signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, RI, GND
  • Flow Control: XON/XOFF, RTS/CTS, DTR/DSR

Check Protocol Matrix for correct software set and P/N

Power

  • 9~48 VDC power input at 3-pin t. block or PoE
  • Power: 6W

Environmental
Operating Temperature: -40 to 85°C
Operating Humidity 5% to 95% Non-condensing

Warranty 5 years

  General Protocol Specifications
IEC61850 Server/ Client
  • Generic access to the data (Read, Write)
  • Clock Synchronization
  • 8 Logical Devices per Port
  • GOOSE (Generic Object Oriented Substation Event) – a GOOSE message will be generated by the gateway automatically upon event(*)
  • (*)Being other protocols not Real-Time, there is no guarantee that GOOSE message is generated within 1 ms from the event itelf.
IEC 60870-5-101 Master/ Slave
  • Protocol implementation with configurable parameters conforms to the IEC 60870-5-101 edition 2 specification
  • Process Information in Monitor and Control Direction
  • Balanced and Unbalanced Modes
  • CP24Time2a or CP56Time2a timestamp for monitor direction report
DNP3 Server/ Client/ Master/ Slave
  • Serial Mode or Ethernet with TCP or UDP Mode
  • Server side supports serving up to 5 client in TCP Mode
  • Client side in a single RS-485 port, supports connecting up to 16 IEDs
  • Client side supports connecting up to 16 IEDs
  • Maximum Fragment size 2048 octets
  • Protocol implementation with configurable parameters conforms to IEEE Std 1815-2012 level 2
IEC 60870-5-103 Master/ Slave
  • Protocol implementation with configurable parameters conforms to the IEC 60870-5-103:1997
  • Master supports connecting up to 16 IEDs
  • Process Information in Monitor and Control Direction
  • Unbalanced Modes
Modbus Server/ Client/ Master/ Slave
  • Support Modbus RTU and ASCII in Serial mode
  • Support Modbus in TCP mode
  • For Modbus Client in TCP mode, support connecting up to 64 Modbus servers
  • For Modbus Server in TCP mode, support serving up to 64 Modbus clients
  • Support maximum number of data points in read direction: 8000 pts
  • Support maximum number of commands in write direction: 4000 pts
IEC 60870-5-104 Server/ Client
  • Server side supports serving up to 5 client
  • Client side supports connecting up to 10 IEDs
  • Protocol implementation with configurable parameters conforms to the IEC 60870-5-104 specification edition 2
  • Process Information in Monitor and Control Direction
  • CP56Time2a timestamp for Control Commands